there are four sub directories: ICH7, ICH8, ICH9 and ICH10. two questions:Ī) I searched through Device Manager, but could not find the SATA ports listed (to update drivers).ī) The drivers are listed under the following file structure: D:\Driver\Chipset\Intel\SATA. Thank you for explaining what to look for why searching for the SATA drivers, I DID find the AHCI files on the CD that came with the board, however. I confirmed the Zip's jumper was set to Master (silly question, but won't the system see two 'Master' devices and, as a result, may cause a conflict?). I sincerely appreciate your help.ġst: I checked the manual for the "SIIG SATA-to-IDE Adapter" but there was no mention of setting the jumpers on the IDE device.Ģnd: I did keep the config of HD (IDE Master) and CD ROM (IDE Slave). Yes, you are correct in your assumption. when I read your suggestion, I kicked myself because I should have known enough to check 'Disk Management.' Alas, all that appears is the HD & CD you say, "recognized in BIOS but not in Win XP Pro", I am assuming you mean that ONLY the device connected via the adapter to a SATA port is not being recognized. working full time and caring for elderly parents. Does that work?įorgive me for the delay in replying. In this structure, you will not be able to boot from the Zip drive, but otherwise it ought to be fully accessible. Win XP should be able to deal with the SATA device since you have given it the required SATA device driver to use after it has booted. Now Install in XP Pro the SATA (or AHCI) driver from the CD that came with your mobo, or get it from the Biostar website. Boot into BIOS Setup and set the SATA Port Mode to Native SATA or AHCI Save and Exit to complete the boot into Win XP Pro. Of course, the Zip drive also will need a power supply connection - maybe through the adapter, depends on how that is built. (I believe your postings say this much works OK.) Set the Zip drive's jumper to Master and connect it to the adapter and then to the SATA port. Set up with the HDD as IDE Master and CD as IDE Slave. Next, let's try something that really ought to work, and make it the simplest arrangement. If the device has different types of "Master" setting, then probably it should be the "Master with no Slave Present". In most cases, I believe it must be set to be this port's MASTER. Check the adapter's manual carefully - what does it say about setting the jumper on the IDE device it is used with? Basically, this adapter creates a type of IDE port, so the device's jumper MUST be set correctly. Is that correct?įirst, I forgot to mention one thing previously. When you say, "recognized in BIOS but not in Win XP Pro", I am assuming you mean that ONLY the device connected via the adapter to a SATA port is not being recognized. In this case you do NOT need to install the SATA device driver in Win XP - as far as it knows, that CD device is behaving as an IDE unit and it does not need and driver for that. Doing this eliminates a couple of handy (but not necessary) features of a true AHCI device, but I think they do not matter at all for optical drives. It works just fine for true SATA HDD's, so maybe it will work for a CD using an adapter such as you have. This sets the BIOS to intervene and make the actual SATA device appear to the OS (Win XP) as a plain old IDE device which it DOES know how to use without added drivers. Go to where the SATA ports are configured, and look for a line about SATA Port Mode. IF you intend to boot from the CD unit, you can try the work-around built into most mobos for the combination of XP and SATA. Of course, if this works, one way to re-arrange is to have your CD back on the IDE port, and the Zip drive on the SATA adapter, since you're more likely to want to boot from the optical drive than from the Zip drive.Ģ. That is because Win XP MUST boot from some non-SATA device first, and in the process access the boot device to load the SATA device Driver before it can use that unit. The LIMIT of this is that you cannot BOOT from this device. Then you can set the SATA Port Mode to SATA or AHCI and use whatever device is connected there as a SATA device. In this way XP can learn how to use a SATA device. That should be on the CD that came with your mobo. IF you intend to use the adapted device (in this case, the CD unit) ONLY for reading and writing AFTER Win XP has loaded, you need to install in XP (while it is running) the SATA port device driver for your mobo. So, assuming your adapter makes the IDE optical unit appear to be a valid SATA device, the BIOS will recognize it (you say it does), but XP will NOT. XP does NOT have "built-in" knowledge (a driver) of SATA devices.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |